Caldo is a growing UK company with more than 20 years experience of supplying hot gas treatment equipment.
Caldo's personnel were involved in the development of hot gas filtration in the late 1980s and 90s and have continued to make innovative developments in hot gas treatment techniques for many demanding applications.
The Caldo office is located in its own premises in Bromsgrove, Worcestershire, England.
Caldo technology is based around the filtration of hot gases using low density ceramic filter elements. This technology is based on:
Caldo has established designs of hot gas filtration equipment in sizes ranging from 36 elements to more than 1000 elements in a single vessel.
Caldo supplies complete pollution control systems for the treatment of hot gases to meet the EC atmospheric emission limits as set out in directive 2000/76/EC.
Caldo works with third parties to develop complete solutions for the incineration of difficult wastes.
Hot gas filters can form the basis for systems to remove all of the pollutants in emissions to atmosphere from incinerators, furnaces, kilns and other high temperature equipment.
Complete systems can comprise some or all of the treatment stages:
Caldo works with a UK company, Explosive and Ordnance Demilitarisation Solutions Ltd (EODS) to design, manufacture and supply complete solutions for the thermal disposal of munitions, typically small arms ammunition.
In this collaboration Caldo supplies engineering design and manufacturing skills to support EODS's knowledge of the end-
Third parties with knowledge of other incinerator opportunities are encouraged to contact Caldo and review their requirements.
Waste gases are often hot and, if they contain fume or dust, Caldo hot gas filters can be used to remove these solids before the gases are released to atmosphere. However, such gases often also contain other pollutants; ceramic filtration can be combined with other techniques to ensure that all of the controlled substances stay within regulatory limits.
Typical waste gases can contain the following classes of pollutants:
With one or two minor exceptions all of these can be controlled / removed by equipment based around a hot gas filter.
The emission of particulates is prevented by passing the gas through a ceramic filter.The filter is at the heart of all the pollution control systems supplied by Caldo. The particulate removal efficiency of ceramic filters greatly exceeds all regulatory requirements.
A major category of regulated pollutants is acid gases as listed above. In the atmosphere these gases dissolve in water to produce the acid rain which is so harmful to the natural environment.
Dry scrubbing is a technique for removing components from a gas by reacting them with a solid and then filtering the gas to remove the solid. For acid gas removal there is a choice of reactive solids between sodium bicarbonate and hydrated calcium oxide (Ca(OH)2 – commonly called called lime); sodium bicarbonate works best at lower temperatures whereas lime is substantially cheaper.
Caldo has pioneered the use of lime at a higher temperature, 400 degC, in conjunction with ceramic filtration to remove it from the gas stream. Operation at this temperature greatly increases the acid gas removal efficiency, reducing operating costs to a minimum.
Caldo has developed a powder feeder for controlling the addition of lime to the gas stream. This compact unit can be sited in a convenient location and it will blow the the metered amount of lime through a small diameter pipe into the inlet duct to the filter.
Also known as afterburning, this is generally the first operation performed on the waste gas. It is done in order to complete the combustion of volatile organic compounds (VOCs) and carbon monoxide (CO) that may remain after the initial burning. It involves heating the gas to 850 degC in the presence on at least 6% of oxygen for a period of at least 2 seconds.
In the past the supplier of the primary combustion stage often also produced the secondary. Increasingly, however, Caldo is being asked to supply complete pollution control systems, including the afterburner. We now supply gas or oil fired afterburners to our own design with a choice of refractory linings.
Dry scrubbing is insufficiently effective for NOx removal and an alternative technique, selective non-
The technical challenge for Caldo was to identify and engineer a system for delivering the NH3 safely and effectively into the process. Ammonia is a toxic chemical, dangerous to ship and store so Caldo sought an alternative. Fortunately a common fertiliser, urea, is soluble in water, decomposes to ammonia when heated and is available as a prilled solid, very safe to handle and ship. Caldo developed the equipment to dissolve the prills in water and spray the solution into the process gas at a controlled pressure.
Company Name | Caldo Engineering Ltd |
Business Category | Energy |
Address | Units 1&2 Schofield Business Park Sugarbrook Road, Aston Fields Bromsgrove United Kingdom |
President | NA |
Year Established | NA |
Employees | NA |
Memberships | NA |
Hours of Operation | NA |
Phone Number | Locked content | Subscribe to view |
Fax Number | Locked content | |
Locked content | ||
Website | Locked content |