Machine Tool Recyclers

We offer top prices and prompt payment for:

• Scrap, used, old, obsolete high-speed steel or tungsten carbide tooling:drills, endmills, inserts, taps, router bits, etc
• Wear parts like compacts, mining bits and saw tips
• Drawing dies, stamping dies, nozzels
• Soft carbide scrap / grinding sludge (payment after analysis—about 4 weeks)

Tungsten Carbide

Tungsten is one of densest of all elements. Pure tungsten is slightly heavier than gold with a specific gravity greater than 19. It has the highest melting point of all elements, 6192 °F, and the highest tensile strength at high temperatures. Recovery of tungsten is what makes scrap carbide valuable.
Tungsten is used in super alloys for the aerospace and other high tech industries, e.g. in the turbines of rockets and jet engines. It is the filament in all incandescent light bulbs and most fluorescents; it’s why Tom Edison is famous. Tungsten is used in armor plate, armor piercing ammunition and bunker buster bombs. Tungsten carbide is used for studs in snow tires and recently to make wedding rings instead of gold, and it is used to make the cutting tools—pictured left—that are used to machine products from automotive engine blocks to dental drills. Tungsten carbide tooling is critical to mining and drilling as well as road construction. 65% of USA tungsten consumption is used in the manufacture of new tungsten carbide.
Tungsten carbide is typically made by a process called sintering, in which different metal powders, having different melting points, are heated to a temperature approximating the lowest melting point—usually cobalt or nickel—which act as the “binders,“ holding together the unmelted particles of the hard carbides, i.e. tungsten. Technically, tungsten is the aggregate and cobalt is the matrix — like the peanuts and caramel in a PayDay candy bar on a microscopic level.
In the famous 1946 Film Noir, GILDA, starring Rita Hayworth in her signature role, George Macready plays a fiendish villain who is going to run the world by establishing a monopoly in tungsten. His theory was that control of a critical material could provide a lot of leverage, kinda like bending someone’s little finger backwards.

Apparently, the Chinese have seen the movie. China is the world’s largest tungsten consumer and producer. Since 2005,the Chinese Government — “in order to conserve its resources and meet increasing domestic demand” — has limited tungsten production and exports while increasing imports of tungsten, scrap carbide and high speed steel.
In response to China’s policies, scrap carbide prices per pound in the United States rose steadily until October 2008, when the price of scrap carbide fell precipitously, like everything else. Towards the end of 2010 and through 2011 and 2012, scrap carbide prices have risen again to near the 2008 highs.
According to the 2013 US Geological Survey, China has 61% of the world’s estimated tungsten reserves which, at its current rate of production, will be exhausted in 43 years. In 2005, the International Tungsten Industry Association estimated that these reserves would last about 140 years. In 2009, China produced 81% of the mined tungsten, world wide.
Because of its great value, reclamation of carbide from scrap is economically feasible. Since 2005, Machine Tool Recyclers has been purchasing tungsten carbide scrap for recovery. In 2011 and 2012 tungsten recycling from scrap accounted for over 50% of tungsten consumption by USA processors and end users, up significantly from 37% in 2010.
For a long time, tungsten carbide's extreme hardness made reclamation difficult. In the late 1960's and early 1970's, a new solution, known as the zinc recovery process, was devised. This process is based on tungsten carbide's reaction with zinc at high temperatures. It is the basis of recovering both hard and soft scrap.
Molten zinc will react with the cobalt (or nickel) in the carbide to cause swelling and cracking of the scrap metal. After this has occurred, the zinc is distilled from the crucible, leaving the scrap in a more brittle state.The carbide is then ground into a powder, usable in new products as an alternative to virgin tungsten.