PLASTAR

Our company has been on the market since 2008 .

Honestly about us: We do not save the planet in a corporate mission, we are open and direct in working with a client. Our goal is the interests of both sides of the signatories of the agreement.

Plants for the processing and disposal of solid waste. Disposal of municipal solid waste as of today is the most acute problem of our time, requiring the use of new methods and technologies. This is explained by the fact that the previously used methods of waste disposal - incineration and disposal in landfills - have shown their impracticality and, moreover, managed to bring a number of countries to the brink of a real environmental disaster. This is due to the fact that such components of garbage as plastic and rubber decompose naturally for quite a long time, and when they are burned, a lot of harmful substances are formed that enter the atmosphere, thereby causing a serious danger to human health.

The issue of the need to recycle used plastic products today in all countries of the world is particularly acute.This is primarily due to the fact that they began to produce quite a lot of plastics, and gradually landfills began to fill with these wastes. Environmentalists began to sound the alarm, since plastic is a non-degradable waste, and if measures are not taken to dispose of it, the planet will soon suffocate in the mountains of plastic. Therefore, in Western countries already in the 60s - 70s of the last century, they began to develop methods for recycling plastic products. Recycling of plastic into granules. In Russia, the problem of plastic recycling became most acute only at the end of 1989, in contrast to industrialized countries. This is explained by the fact that plastic food packaging used for a long time all over the world in the USSR began to be used much later. The growth in the amount of produced plastic food packaging and disposable plastic tableware has led to the accumulation of a fairly large amount of this type of waste at landfills. However, despite this, in Russia at the end of the last century, the attitude to the problem of plastic recycling was much simpler, because, firstly, few people thought about its harmful effects on the environment, and, secondly, there was no normal legislative framework in the country for the protection of our environment. Therefore, the need to recycle plastic as a problem has been talked about relatively recently. And today, based on the experience of Western countries, the following methods of processing plastic waste have begun to be applied in Russia. in Russia at the end of the last century, the attitude to the problem of plastic recycling was much simpler, because, firstly, few people thought about its harmful effects on the environment, and, secondly, there was no normal legislative framework in the country to protect our environment. Therefore, the need to recycle plastic as a problem has been talked about relatively recently. And today, based on the experience of Western countries, the following methods of processing plastic waste have begun to be applied in Russia. in Russia at the end of the last century, the attitude to the problem of plastic recycling was much simpler, because, firstly, few people thought about its harmful effects on the environment, and, secondly, there was no normal legislative framework in the country to protect our environment. Therefore, the need to recycle plastic as a problem has been talked about relatively recently. And today, based on the experience of Western countries, the following methods of processing plastic waste have begun to be applied in Russia. Therefore, the need to recycle plastic as a problem has been talked about relatively recently. And today, based on the experience of Western countries, the following methods of processing plastic waste have begun to be applied in Russia. Therefore, the need to recycle plastic as a problem has been talked about relatively recently. And today, based on the experience of Western countries, the following methods of processing plastic waste have begun to be applied in Russia.

Plastic recycling technologies.The current methods of processing plastic waste can be divided into two main groups: physical-chemical, mechanical. All mechanical methods of processing plastic waste for the purpose of their recycling consist in the grinding of various plastic substances, such as undrawn or partially drawn fibers, off-grade tape and casting waste. During this processing, crumb and powder materials are formed, which are subjected to injection molding. This method, based on mechanical grinding, does not lead to a change in the physicochemical properties of plastics and their structure. Recycling of plastic by physical and chemical methods can be carried out in one of the following ways: The method of destruction of plastic waste. This technology makes it possible to obtain polygomers and monomers, which are used to produce fibers and films. remelting method. This method of processing plastic waste allows the production of granules using injection molding or extrusion technology. Method of reprecipitation from solutions. This processing method makes it possible to produce composite materials and obtain powders used for applying polymer coatings. Method of chemical modification. This method makes it possible to produce materials with new physical and chemical properties. The most common of all the plastic waste recycling methods listed above is the remelting method, or, as it is also called, the granulation or tableting method. This method of processing plastic waste allows the production of granules using injection molding or extrusion technology. Method of reprecipitation from solutions. This processing method makes it possible to produce composite materials and obtain powders used for applying polymer coatings. Method of chemical modification. This method makes it possible to produce materials with new physical and chemical properties. The most common of all the plastic waste recycling methods listed above is the remelting method, or, as it is also called, the granulation or tableting method. This method of processing plastic waste allows the production of granules using injection molding or extrusion technology. Method of reprecipitation from solutions. This processing method makes it possible to produce composite materials and obtain powders used for applying polymer coatings. Method of chemical modification. This method makes it possible to produce materials with new physical and chemical properties. The most common of all the plastic waste recycling methods listed above is the remelting method, or, as it is also called, the granulation or tableting method. used for applying polymer coatings. Method of chemical modification. This method makes it possible to produce materials with new physical and chemical properties. The most common of all the plastic waste recycling methods listed above is the remelting method, or, as it is also called, the granulation or tableting method. used for applying polymer coatings. Method of chemical modification. This method makes it possible to produce materials with new physical and chemical properties. The most common of all the plastic waste recycling methods listed above is the remelting method, or, as it is also called, the granulation or tableting method. Granulation of plastic waste.Plastic Waste Pelletizing There are two main methods of waste plastic pelletizing today: cold pelletizing and hot pelletizing. The resulting material has the form of a plastic tape. Then these tapes are hot cut by stationary rotating knives into small granules or tablets. After that, the process of cooling the obtained granules with an air flow takes place. In the cold granulation method, the polymer is forced through a perforated plate, resulting in plastic tapes. These tapes are immediately cooled. After cooling is completed, the strips are cut into granules using rotating knives. Liquid nitrogen can be used to prevent heating of the material during the cutting process.

The development of plastic recycling.Today, the plastics recycling plant is a fairly profitable business, since the global demand for recycled plastic, according to experts from The Freedonia Group, will grow by an average of 6.5% annually. Moreover, according to their own forecasts, by 2016 the market for recycled plastic will amount to more than 1.6 billion tons. And this is taking into account the fact that, at the same time, the volume of recycled plastic in the world today does not exceed 7%. Experts explain such growth prospects in this direction by several main factors. A fairly important role here is played by the desire of manufacturers of goods and packaging to be environmentally friendly. Practical aspects are also important here: today there is a development of technologies for sorting municipal solid waste and recycling, which increases the amount of plastic waste, which can be recycled and obtain high quality material. Experts also predict an improvement in the infrastructure for collecting household waste, which will lead to an increase in the level of plastic recycling. Thus, experts believe that the recycling of plastic waste in the near future may become an even more profitable business than it is now. Moreover, this forecast, first of all, is calculated for Western countries, in which the process of plastic processing has gone far ahead in comparison with us. In Russia, this niche is practically not occupied, which, given global trends, is quite attractive from a business point of view. In addition, new laws are constantly being introduced in the country that take care of environmental protection and the need to process household waste, which indicates that